Optoma DLP Projector User Manual (2023)

User Manual for Optoma models including: DLP Projector

DLP Projector - Optoma

Any operation or adjustment not specifically instructed in the User manual creates the risk of hazardous laser radiation exposure. ‡. Do not open or disassemble ...

Bedienungsanleitung

Optoma ZU660 ab €9958,00 (2019) | Preisvergleich Geizhals Österreich

Manual

Optoma Proscene ZU660 Laser projector (ZU660)

Not Your Device? Search For Manuals / Datasheets:

File Info : application/pdf, 65 Pages, 14.01MB

Document
4cdf0df4-fe5d-4f84-ad99-274c19c1a5b5
DLP® ProjectorUser manualTABLE OF CONTENTSSAFETY ............................................................................................... 4Important Safety Instruction....................................................................................................... 4 Laser Radiation Safety Information ........................................................................................... 5 Copyright ................................................................................................................................... 6 Disclaimer.................................................................................................................................. 6 Trademark Recognition ............................................................................................................. 6 FCC ........................................................................................................................................... 6 Declaration of Conformity for EU countries ............................................................................... 7 WEEE ........................................................................................................................................ 7INTRODUCTION .................................................................................. 8Package Overview..................................................................................................................... 8 Standard accessories ................................................................................................................ 8 Optional accessories ................................................................................................................. 8 Product Overview ...................................................................................................................... 9 Connections.............................................................................................................................. 10 Keypad ..................................................................................................................................... 11 Remote control ......................................................................................................................... 12SETUP AND INSTALLATION ............................................................. 13Installing the projection lens ..................................................................................................... 13 Adjusting the projector position ................................................................................................ 15 Connecting sources to the projector......................................................................................... 16 Adjusting the projector image ................................................................................................... 17 Remote setup ........................................................................................................................... 18USING THE PROJECTOR.................................................................. 20Powering on / off the projector.................................................................................................. 20 Selecting an input source ......................................................................................................... 21 Menu navigation and features .................................................................................................. 22 OSD Menu tree......................................................................................................................... 23 Picture menu ............................................................................................................................ 30 Screen menu ............................................................................................................................ 34 Settings menu........................................................................................................................... 39 Light source menu .................................................................................................................... 40 Options menu ........................................................................................................................... 41 3D menu ................................................................................................................................... 43 Communications menu............................................................................................................. 44 Setup network control settings menu ....................................................................................... 462 EnglishADDITIONAL INFORMATION ............................................................ 51Compatible resolutions ............................................................................................................. 51 Image size and projection distance .......................................................................................... 56 Projector dimensions and ceiling mount installation................................................................. 57 IR remote codes ....................................................................................................................... 58 Troubleshooting ........................................................................................................................ 60 Warning indicators.................................................................................................................... 61 Specifications ........................................................................................................................... 63 Optoma global offices............................................................................................................... 64English 3SAFETYThe lightning flash with arrow head within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.Please follow all warnings, precautions and maintenance as recommended in this user's guide.Important Safety Instruction Do not block any ventilation openings. To ensure reliable operation of the projector and to protect from over heating, it is recommended to install the projector in a location that does not block ventilation. As an example, do not place the projector on a crowded coffee table, sofa, bed, etc. Do not put the projector in an enclosure such as a book case or a cabinet that restricts air flow. To reduce the risk of fire and/or electric shock, do not expose the projector to rain or moisture. Do not install near heat sources such as radiators, heaters, stoves or any other apparatus such as amplifiers that emits heat. Do not let objects or liquids enter the projector. They may touch dangerous voltage points and short out parts that could result in fire or electric shock. Do not use under the following conditions: ± In extremely hot, cold or humid environments. (i) Ensure that the ambient room temperature is within 5°C ~ 40°C (ii) Relative humidity is 10% ~ 85% ± In areas susceptible to excessive dust and dirt. ± Near any appliance generating a strong magnetic field. ± In direct sunlight. Do not use the projector in places where flammable gases or explosives gases may be present in the atmosphere. The lamp inside the projector becomes very hot during operation and the gases may ignite and result in a fire. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to): ± Unit has been dropped. ± Power supply cord or plug has been damaged. ± Liquid has been spilled on to the projector. ± Projector has been exposed to rain or moisture. ± Something has fallen in the projector or something is loose inside. Do not place the projector on an unstable surface. The projector may fall over resulting in injury or the projector may become damaged. Do not block the light coming out of the projector lens when in operation. The light will heat the object and cause melt, burns or start a fire. Please do not open or disassemble the projector as this may cause electric shock. Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerousvoltages or other hazards. Please call Optoma before you send the unit for repair. See projector enclosure for safety related markings. The unit should only be repaired by authorized service personnel.4 English Only use attachments/accessories specified by the manufacturer. Do not look into straight into the projector lens during operation. The bright light may harm your eyes. This projector will detect the life of the lamp itself. When switching the projector off, please ensure the cooling cycle has been completed beforedisconnecting power. Allow 90 seconds for the projector to cool down. Turn off and unplug the power plug from the AC outlet before cleaning the product. Use a soft dry cloth with mild detergent to clean the display housing. Do not use abrasive cleaners,waxes or solvents to clean the unit. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Do not setup the projector in places where it might be subjected to vibration or shock. Do not touch the lens with bare hands. Remove battery/batteries from remote control before storage. If the battery/batteries are left in theremote for long periods, they may leak. Do not use or store the projector in places where smoke from oil or cigarettes may be present, as itcan adversely affect the quality of the projector performance. Please follow the correct projector orientation installation as non standard installation may affect theprojector performance. Use a power strip and or surge protector. As power outages and brown-outs can KILL devices.Laser Radiation Safety InformationThis product is classified as CLASS 1 LASER PRODUCT - RISK GROUP 2 of IEC 60825-1 : 2014 and also complies with 21 CFR 1040.10 and 1040.11 as a Risk Group 2 , LIP ( Laser Illuminated Projector) as defined in IEC 62471:2006 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007., ( & & / $ 6 6/ $ 6 ( 53 52 ' 8 & 75 , 6 .* 52 8 3 &RPSOLHVZLWK&)5DQGDVD5LVN*URXS/,3 /DVHU,OOXPLQDWHG3URMHFWRUDVGHILQHGLQ,(&H[FHSWIRUGHYLDWLRQV SXUVXDQWWR/DVHU1RWLFH1RGDWHG-XQH &$87,21 3RVVLEO\KD]DUGRXVRSWLFDOUDGLDWLRQHPLWWHGIURPWKLVSURGXFW'RQRWVWDUHDW RSHUDWLQJEHDP0D\EHKDUPIXOWRWKHH\HV , ( & 3 52 ' 8 , 7/ $ 6 ( 5' (& / $ 6 6 (* 52 8 3 (' (5 , 6 4 8 ( $9(57,66(0(17 5D\RQQHPHQWRSWLTXHGDQJHUHX[SRWHQWLHOpPLVSDUFHSURGXLW1HSDVUHJDUGHU GLUHFWHPHQWGDQVOHIDLVFHDX&HFLSRXUUDLWrWUHQRFLISRXUOHV\HX[ ,(&5* ,(&5* Failure to comply with the following could result in death or serious injury. This projector has a built-in Class 4 laser module. Never attempt to disassemble or modify theprojector. Any operation or adjustment not specifically instructed in the User manual creates the risk ofhazardous laser radiation exposure. Do not open or disassemble the projector as this may cause damage or exposure to laser radiation. Do not stare into beam when the projector is on. The bright light may result in permanent eye damage. When turning on the projector, make sure no one within projection range is looking into the lens. Follow the control, adjustment, or operation procedures to avoid damage or injury from exposure oflaser radiation. The instructions for the assembly, operation, and maintenance include clear warnings concerningprecautions to avoid possible exposure to hazardous laser radiation.English 5CopyrightThis publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.© Copyright 2018DisclaimerThe information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.Trademark RecognitionKensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. DLP®, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a trademark of Texas Instruments. HDBaseTTM and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance. All other product names used in this manual are the properties of their respective owners and are Acknowledged.FCCThis device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the device and receiver. Connect the device into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help.Notice: Shielded cables All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.Caution Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector. Operation Conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference and 2. This device must accept any interference received, including interference that may cause undesired operation.6 EnglishNotice: Canadian users This Class A digital apparatus complies with Canadian ICES-003. Remarque à l'intention des utilisateurs canadiens Cet appareil numerique de la classe A est conforme a la norme NMB-003 du Canada.Declaration of Conformity for EU countries EMC Directive 2014/30/EU (including amendments) Low Voltage Directive 2014/35/EU Radio Equipment Directive 2014/53/EU (if product has RF function) RoHS Directive 2011/65/EUWEEEDisposal instructions Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle it.English 7INTRODUCTIONPackage OverviewCarefully unpack and verify that you have the items listed below under standard accessories. Some of the items under optional accessories may not be available depending on the model, specification and your region of purchase. Please check with your place of purchase. Some accessories may vary from region to region. The warranty card is only supplied in some specific regions. Please consult your dealer for detailed information.Standard accessoriesONOFF123456789Info 0 ModeAutoInputEnterMenuExitGamma Bright Cont. PIPLens HFocusLens VKeystone HZoomKeystone VShutter (AV Mute)Hot KeyPatternProjectorRemote control2x AAA batteriesPower leadVGA cableLens cover*Optional accessories CD User Manual Warranty Card Basic User ManualDocumentationOptional lens A01 (0.95-1.22)Optional lens A02 (1.22-1.53)Optional lens A03 (1.53-2.92)Optional lens A13 (2.90-5.50)Optional lens A15 (0.75-0.95)Optional UST lens A16 (0.36)Note: 8 EnglishOptional accessories vary depending on model, specification and region. *For A01, A03, and A13 lens.INTRODUCTIONProduct Overview12345 613 71211 10 9 8Note: Do not block projector inlet or outlet air vents. (*) optional accessory varies depending on model, specification, and region.NoItem1. Front IR Receiver2. Lens3. Top IR Receiver4. LED Status Indicators5. Tilt-Adjustment Feet6. Ventilation (inlet)7. Ventilation (outlet)NoItem8. Power Switch9. Power Socket10. KensingtonTM Lock Port11. Security Bar12. Input / Output13. KeypadEnglish 9INTRODUCTIONConnections1 2 345612 1110 987NoItem1. LAN Connector2. HDBaseT Connector3. HDMI-1 Connector4. HDMI-2 Connector5. DVI-D Connector6. VGA-IN/YPbPr ConnectorNoItem7. Wired Remote Connector8. Power Socket9. VGA-OUT Connector10. RS232-C Connector11. 3D SYNC OUT Connector12. 3D SYNC IN Connector10 EnglishINTRODUCTIONKeypad1234511 10 98 76No 1. Power 2. Menu 3. Enter 4. Exit 5. Input 6. AV MuteItemNoItem7. Four Directional Select Keys8. Zoom9. Focus10. Auto11. LensEnglish 11INTRODUCTIONRemote controlONOFF11612324567893Info 0 Mode174AutoInput1856Enter7MenuExit198Gamma Bright Cont. PIP2092110Lens HFocus2211 Lens V12Keystone HZoom2313Keystone V14Shutter (AV Mute)Hot KeyPattern2415NoItem1. Power On2. Number Keys3. Info4. Auto5. Enter6. Four Directional Select Keys7. Menu8. GammaNoItem9. Bright10. Lens H11. Lens V12. Keystone H13. Keystone V14. Shutter (AV Mute)15. Hot Key16. Power Off12 EnglishNo 17. Mode 18. Input 19. Exit 20. PIP 21. Cont. 22. Focus 23. Zoom 24. PatternItemSETUP AND INSTALLATIONInstalling the projection lensBefore setting up the projector, install the projection lens on the projector.IMPORTANTT! Make sure the projector is properly turned off before installing the lens. During lens installation, do not adjust the lens shift, zoom, or focus either using the remote control or the projector keypad.Procedure: 1. Rotate the lens cap counterclockwise.2. Remove the lens cap.English 13SETUP AND INSTALLATION3. Install the lens onto the projector.4. Rotate the lens clockwise to lock the lens in place.5. Firmly install the lens ring onto the lens.Note: The lens ring is compatible with the following lens modules: A01 (0.95-1.22), A02 (1.22-1.53), A03 (1.532.92), and A13 (2.90-5.50).14 EnglishSETUP AND INSTALLATIONAdjusting the projector positionWhen you select a position for the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Follow these general guidelines: Position the projector on a flat surface at a right angle to the screen. The projector (with the standard lens) must be at least 3 feet (0.9m) from the projection screen. Position the projector to the desired distance from the screen. The distance from the lens of the projector to the screen, the zoom setting, and the video format determine the size of the projected image. For the fixed short lens, the image exits at a default angle. However, the lens shift feature makes the image offset variable. 360 degree free orientation operationEnglish 15SETUP AND INSTALLATIONConnecting sources to the projector3 21456 71211108NoItem1. RJ-45 Cable2. CAT5e/6/6A Cable3. HDMI Cable4. DVI-D Cable5. VGA-In Cable6. RCA Component Cable16 English9NoItem7. Wired Remote-In Cable (~30m)8. Power Cord9. VGA-Out Cable10. RS-232C Cable11. 3D Emitter Cable12. 3D Sync CableSETUP AND INSTALLATIONAdjusting the projector imageImage height The projector is equipped with elevator feet for adjusting the image height.1. Locate the adjustable foot you wish to adjust on the underside of the projector. 2. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector.Tilt-Adjustment FeetTilt-Adjustment RingWarning: The feet of projector are not removable. Please do not screw out the feet of projector. The adjustable height of the elevator feet could be raised up to 45mm.Zoom and focusTo adjust the image size, press the Zoom button ( A ) to increase or decrease the projected imagesize.To adjust the focus, press the Focus button ( B ) until the image is sharp and legible.Lens HFocusLens VBKeystone HZoomKeystone VShutter (AV Mute)Hot KeyPatternAEnglish 17SETUP AND INSTALLATIONRemote setupInstalling / replacing the batteries Two AAA size batteries are supplied for the remote control.1. Remove the battery cover on the back of the remote control. 2. Insert AAA batteries in the battery compartment as illustrated. 3. Replace back cover on remote control.Note: Replace only with the same or equivalent type batteries.CAUTION Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. Do not mix batteries of different types. Different types of batteries have different characteristics. Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries orcause chemical leakage in old batteries. Remove batteries as soon as the are depleted. Chemicals that leak from batteries that come in contactwith skin can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth. The batteries supplied with this product may have a shorter life expectancy due to storage conditions. If you will not be using the remote control for an extended period of time, remove the batteries. When you dispose of the batteries, you must obey the law in the relative area or country. Effective range Infra-Red (IR) remote control sensors are located on the front and top sides of the projector. Ensure to hold the remote control at an angle within ±30° (horizontally or vertically) to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not be longer than 10 meters (32.8 feet). Make sure that there are no obstacles between the remote control and the IR sensor on the projectorthat might obstruct the infra-red beam. Make sure the IR transmitter of the remote control is not being shined by sunlight or fluorescent lampsdirectly. Please keep the remote controller away from fluorescent lamps for over 2 m or the remote controllermight become malfunction. If the remote control is closed to Inverter-Type fluorescent lamps, it might become ineffective from timeto time. If the remote control and the projector are within a very short distance, the remote control mightbecome ineffective. When you aim at the screen, the effective distance is less than 5 m from the remote control to thescreen and reflecting the IR beams back to the projector. However, the effective range might change according to screens.18 EnglishPatternKeystonSKe(heAuyHVttsteMruotne)e V Hot KeyZoomFocusLens H Lens VExit PIPCont.MenGuamma BrightEnterInputMode90Info Auto6835724OFF1ONSETUP AND INSTALLATIONApprox. ±30° Approx. ±30°English 19ONOFF123456789Info 0 ModeAutoInputEnterMenuExitGamma Bright Cont. PIPLens HFocusLens VKeystone HZoomKeystone VShutter (AV Mute)Hot KeyPatternUSING THE PROJECTORPowering on / off the projectorONOFFor123Powering on 1. Securely connect the power lead and signal/source cable.2. Set the Power switch to the "ON" position.3. Turn on the projector by pressing " " on the remote control or pressing " " on the projector keypad. The Status LED is Orange with a long blink.Note: The first time the projector is turned on, you will be prompted to select the preferred language, projection orientation, and other settings.Powering off1. Turn off the projector by pressing " " on the projector keypad or pressing " A warning message will appear on the displayed image." on the remote control.Power Off? Press power key again.2. Press " " on the projector keypad or press " " on the remote control again to confirm, otherwise the warning message will disappear after 10 seconds. When you press " " on the projector keypad or press " " on the remote control for the second time, the projector will shut down.3. Set the Power switch to the "OFF" position. 4. Disconnect the power lead from the electrical outlet and the projector. Note: It is not recommended that the projector is turned on immediately, right after a power off procedure.20 EnglishUSING THE PROJECTORSelecting an input sourceTurn on the connected source that you want to display on the screen, such as computer, notebook, video player, etc. The projector will automatically detect the source. If multiple sources are connected, press the Input button on the projector keypad or the remote control to select the desired input.Info 0 ModeAutoInputorEnterEnglish 21USING THE PROJECTORMenu navigation and featuresThe projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source.1. To open the OSD menu, press "Menu" on the remote control or the projector keypad. 2. When OSD is displayed, use pqtu to navigate within the menu and adjust a setting up or down. 3. Press "Enter" to enter the submenu or confirm the selection/setting. 4. Press "Exit" to return to the previous menu or exit menus if at top level.Main MenuSub MenuDisplay Mode Wall ColorBrightness Contrast Sharpness Color Tint Gamma White PeakingColor Temp. Color Wheel Speed HSG Adjustment Contrast Enhancement Color Space Save to UserPicturePresentation WhiteVideo BrightOff AutoSettingsSelectEnterExit22 EnglishUSING THE PROJECTOROSD Menu treeMain MenuSub Menu Display ModeWall color BrightnessSub Menu 2 Bright Presentation Movie sRGB Blending DICOM SIM. User White Gray 130Contrast SharpnessColorPictureTintGammaWhite Peaking Color Temp. Color Wheel SpeedVideo Film Bright CRT DICOMWarm Bright Cool 2X 3XRedGreenHSG Adjustment BlueCyanMagentaSub Menu 3Default ValueDepends on signal type and selected Color Mode.RangeHue Saturation Gain Hue Saturation Gain Hue Saturation Gain Hue Saturation Gain Hue Saturation GainWhiteDepends on Color Mode.Depends on Color Mode.5For VGA component signal only.For VGA component signal only.0 ~ 100 0 ~ 100 0 ~ 10 0 ~ 1000 ~ 100Depends on Color Mode.Bright0 ~ 1003X1~199 0 ~ 199 1 ~ 199 1~199 0 ~ 199 1 ~ 199 1~199 0 ~ 199 1 ~ 199 1~199 0 ~ 199 1 ~ 199 1~199 0 ~ 199 1 ~ 199English 23USING THE PROJECTORMain MenuSub MenuSub Menu 2YellowHSG Adjustment White GainPicture ScreenReset to DefaultContrast EnhancementOff Dynamic Black Extreme BlackAutoColor SpaceRGB (0-255) RGB (16-235)YUVYes Save to UserNoAuto4:3Aspect Ratio16:916:10NativePixel PhasePixel TrackHorz PositionVert PositionDigital Horz Zoom100% to 200%Digital Vert Zoom100% to 200%Digital Horz ShiftDigital Vert ShiftOffCeiling Mount OnAutoOff Rear ProjectionOnH. KeystoneV. KeystoneGeometric Correction4-CornerSub Menu 3 Hue Saturation Gain Red Green BlueDefault ValueRange 1~199 0 ~ 199 1 ~ 1991~199OffAutoAnalog signal only. Analog signal only. Analog signal only. Analog signal only.0 ~ 100 0 ~ 100 0 ~ 100 0 ~ 10000 ~ 1000 ~ 10500 ~ 100500 ~ 100AutoOff2020Top Left Horz Adjust Top Left Vert Adjust Top Right Horz Adjust Top Right Vert Adjust Bottom Left Horz Adjust0 ~ 40 0 ~ 4024 EnglishUSING THE PROJECTORMain MenuSub MenuGeometric CorrectionScreenPIP-PBPSource key Auto ImageSource InfoSub Menu 24-CornerGrid Color ResetPIP / PBP EnableMain SourceSub SourceLayoutSize Swap Change Sources List all Sources Auto Source Normal Wide Active Source Signal Format Aspect Ratio Resolution Vert Refresh Horz Refresh Pixel Clock Sync Type Color SpaceSub Menu 3Default ValueBottom Left Vert AdjustBottom Right Horz AdjustBottom Right Vert AdjustPurple GreenGreenYesNoOffPBPOffPIPVGAHDMI-1HDMI-2Current source.DVIHDBaseTVGAHDMI-1 HDMI-2 DVIDepends on current source.HDBaseTTop LeftTop Right Bottom LeftTop LeftBottom RightSmallMediumMediumLargeWideRangeEnglish 25USING THE PROJECTORMain Menu ScreenSettingsLight sourceSub MenuSub Menu 2Source Info LanguagePIP/PBP (When PIP/PBP is active)  (When PIP/ PBP is active)EnglishSimplified ChineseFrenchGermanItalianJapanese Korean Russian SpanishPortugueseIndonesianDutchLeft TopRight TopMenu Location CenterLeft BottomStandby Power ModeTest PatternDirect Power OnHot-Key settingsReset to Default Service Light Source Mode Constant PowerRight Bottom 0.5W mode Communication mode None Grid White Black Checkerboard Color Bars Off On Blank Screen Aspect Ratio Freeze Screen Projector Info Yes NoConstant Power Constant Intensity ECO 1 ECO 2 0 to 99Sub Menu 3Default ValueRangeEnglishLeft Top Communication None Off Blank ScreenConstant Power990 to 99 (30% to 100%)26 EnglishUSING THE PROJECTORMain Menu Light sourceOptionsSub MenuSub Menu 2Total Projector Light Source Info HoursLD HoursLogoBackground colorBlue BlackWhiteAuto shutdownSleep TimerFocusSub Menu 3 CommandZoomCommandLens ShiftCommandLens FunctionApply PositionLens MemorySave Current PositionHigh Altitude PINLock Lens Motors Lens Calibration Off On PIN protectChange PIN TopFront Remote SettingsHDBaseTShow messageProjector Address Off OnAllow Locked CommandOff OnOff On Off On Off On 0 ~ 99Default ValueRangeDefault Value0 01 2 3 4 5 1 2 3 4 5 Allow0~120 (one step: 5 mins)0~990 (one step: 10 mins)Focus in - motor go stepFocus out - motor go stepZoom in - motor go stepZoom out - motor go stepLeft shift up - motor go stepLeft shift down - motor go stepLeft shift right - motor go stepLeft shift left - motor go stepOff OffOn On On 0 OffEnglish 27USING THE PROJECTORMain MenuSub MenuLED SettingsOptionsInformationSub Menu 2Sub Menu 3Default ValueKeypad LEDStatus LEDModel Name Serial Number Native Resolution MCU FW DDP FW M9813 FW Motor FW ext flash FW Main Input Main Signal Format Main Pixel Clock Main Sync Type Main Horz Refresh Main Vert Refresh PIP/PBP Input PIP/PBP Signal Format PIP/PBP Pixel Clock PIP/PBP Sync Type PIP/PBP Horz Refresh PIP/PBP Vert Refresh Light Source Power Total Projector Hours Light Source Hours Standby Mode Lens Lock Settings IP Address DHCP System TemperatureAlways OnAlways Off Always On Always Off Warnings/Errors OnlyAlways On Always OnRange28 EnglishUSING THE PROJECTORMain MenuSub Menu 3D3D Invert3D FormatSub Menu 2Auto On Off On Frame Packing Side-by-Side (Half) Top and BottomSub Menu 33D Communications1080p @ 24 3D sync out Frame Delay L/R Reference DLP LinkLANNetworkSerial Port Baud RateSerial Port Echo Serial Port PathFrame Sequential96Hz 144Hz To Emitter To Next Projector1ST Frame Field GPIO Off On DHCP IP Address Subnet Mask Default Gateway MAC Address Apply Projector NameShow Network MessagesRestart Network... Network Factory Reset... 1200 2400 4800 9600 14400 19200 38400 57600 115200 Off On RS232 HDBaseTCommandOn Off Command CommandDefault Value AutoRangeOffDepends on input signal. If an HDMI source is detected with AVINFO then 3D mode is switched on automatically.144HzTo Emitter 1ST Frame1~200OffBy set.By set.115200Off RS232English 29USING THE PROJECTORPicture menuDisplay Mode Wall ColorBrightness Contrast Sharpness Color Tint Gamma White PeakingColor Temp. Color Wheel Speed HSG Adjustment Contrast Enhancement Color Space Save to UserPicturePresentation WhiteVideo BrightOff AutoSelectEnterExitDisplay ModeOptimize the projector for displaying images under certain conditions. Bright: Maximum brightness from PC input. Presentation: This mode is suitable for showing PowerPoint presentations when the projector isconnected to the PC. Movie: This mode is suitable for watching video. sRGB: This color mode matches the REC709 color standard as closely as possible. Blending: When using multiple projectors, this mode can eliminate the visible banding and create asingle bright, high resolution image across the screen. DICOM SIM: This mode can project a monochrome medical image such as an X ray radiography, MRI,etc. User: Memorize user's settings.Wall ColorSet the wall color so that the projector can enhance the color performance customized for the specific wall. Available options include White and Gray 130.BrightnessAdjust the intensity of the image. ContrastAdjust the degree of difference between the lightest and darkest parts of the image and change the amount of black and white in the image. SharpnessAdjust the sharpness of the image.30 EnglishUSING THE PROJECTORColor Adjust a video image from black and white to fully saturated color. Tint Adjust the color balance of red and green. Gamma Set up gamma curve type. After the initial setup and fine tuning is completed, utilize the gamma adjustment steps to optimize your image output. Video: For video or TV source. Film: For home theater. Bright: For emphasizing brightness. CRT: For CRT monitor. DICOM: For simulated DICOM. White Peaking Increase the brightness of whites near 100%. Color Temp. Change the intensity of the colors. Select a listed relative warmth value. Color Wheel Speed Select the color wheel speed from 2x or 3x. The color wheel speed defines the delay between the color wheel and the DMD. HSG Adjustment For more information on HSG adjustment, refer to page 31. Contrast Enhancement Enable or disable the contrast enhancement function. Enable this function to raise the contrast ratio. Off: Disable contrast enhancement function. Dynamic Black: Auto adjust the contrast ratio for video contents. Extreme Black: Auto increase contrast when a blank (black) image is displayed. Color Space Select a color space specifically tuned for the input signal. Only useful for analog signals and certain digital sources. The available options include Auto, RGB (0-255), RGB (16-235), and YUV. Save to User Save the current picture settings in user profile.HSG Adjustment menuHSG AdjustmentRedHueSaturationGainReset to DefaultSelectAdjustExitEnglish 31USING THE PROJECTORHue Note the following about adjusting hue: Adjust the hue independently for each color (R,G,B,C,M, and Y). White does not have a hue input. A negative hue input provides a clockwise rotation of the color's hue. A positive hue input provides a counter-clockwise rotation of the color's hue. A zero input does not change the hue of the color.Saturation Note the following about adjusting saturation: The saturation can be adjusted independently for each color (R,G,B,C,M, and Y). A saturation level of 0 removes all color from that region. A saturation level of 254 sets the color region to have maximum color. A saturation level of 127 does not change the saturation.32 EnglishUSING THE PROJECTORGain Note the following about adjusting gain: The gain can be adjusted independently for each color (R,G,B,C,M,Y, and W). The range of input is 0 to 254. The gain changes the intensity level of the respective color. A gain level of 127 disables the HSG controls for that color. A gain level less than 127 darkens the respective color. A gain level of 254 sets the color region to have maximum gain; however, clipping occurs on thesignal. A gain of 127 is the nominal setting. White provides three gain level controls, one each for the R,G,B component of white. Reset to Default Reset all the HSG adjustments to the factory defaults.English 33USING THE PROJECTORScreen menuAspect Ratio Pixel PhasePixel Track Horz Position Vert Position Digital Horz Zoom Digital Vert Zoom Digital Horz Shift Digital Vert ShiftCeiling Mount Rear Projection Geometric Correction PIP-PBP Source Key Auto Image Source InfoScreenAutoAuto OffChange Sources WideSelectEnterExitAspect RatioDisplay an image with the detected size, or resize the image by maximizing either the height, width, both, or resize to the maximum size possible while keeping the original aspect ratio. Auto: Display with the detected size. 4:3: Retain 4:3 aspect ratio. 16:9: Retain 16:9 aspect ratio. 16:10: Retain 16:10 aspect ratio. Native: This format displays the original image without any scaling. Pixel PhaseAdjust the pixel phase when the image shows shimmer or noise after pixel tracking is optimized. Pixel phase can adjust the phase of the pixel-sampling clock relative to the incoming signal. (Analog RGB signals only.) Pixel TrackEnsure that the image quality is consistent across the screen, the aspect ratio is maintained, and the pixel phase can be optimized. Steady flickering or several soft vertical stripes or bands across the entire image indicates poor pixel tracking. (Analog RGB signals only). Horz PositionMove the image right or left within the area of available pixels. Vert PositionMove the image up or down within the area of available pixels. Digital Horz ZoomChange the size of projector's display area horizontally. If the display area has been resized by this setting, it can be moved by changing the Digital Horz Shift.34 EnglishUSING THE PROJECTORDigital Vert Zoom Change the size of projector's display area vertically. If the display area has been resized by this setting, it can be moved by changing the Digital Vert Shift settings. Digital Horz Shift Move the display area horizontally if its size has been changed by the Digital Horz Zoom setting. Digital Vert Shift Move the display area vertically if its size has been changed by the Digital Vert Zoom setting. Ceiling Mount Turn the image upside down for ceiling-mounted projection. Rear Projection Reverse the image so that you can project from behind a translucent screen. Geometric Correction Provide several ways for warping control. For more information on geometry correction, refer to page 35. H. Keystone: Adjust the keystone horizontally and make a more square image. V. Keystone: Adjust the keystone vertically and make a more square image. 4-Corner: Allow the image to be squeezed to fit an area defined by moving each of the four corners' xand y position. Grid Color: Choose the color of 4 corner, green or purple. Reset: Restore the settings to its default value. PIP-PBP Display an image with two sources in PIP mode or PBP mode. For more information on PIP/PBP, refer to page 36. Source Key List or change the sources. The available options include Change Sources, List all Sources, and Auto Source. Auto Image Force the projector to reacquire and lock to the input signal. This is useful when signal quality is marginal. Normal: Supports all of the 4:3 input sources. Wide: Supports all of the 16:9 input source and most of the 4:3 input sources.Note: For the 4:3 input sources not recognized by Wide mode (for example, 1400x1050), perform Auto Image using Normal mode. Source Info Display the current source settings. (Read-only).Geometric Correction menuGeometric CorrectionH. KeystoneV. Keystone 4 - cornerGrid ColorResetSelectEnterGreen ExitEnglish 35USING THE PROJECTORH. Keystone Adjust image distortion horizontally and make a squarer image. Horizontal keystone is used to correct a keystoned image shape in which the left and right borders of the image are unequal in length. This is intended for use with horizontally on-axis applications.V. KeystoneAdjust image distortion vertically and make a squarer image. Vertical keystone is used to correct a keystoned image shape in which the top and bottom are slanted to one of the sides. This is intended when for use with vertically on-axis applications.4-Corner Allow the image to be squeezed to fit an area defined by moving each of the four corners' x and y position. Top Left Horz Adjust (B) / Top Left Vert Adjust (A): Top left corner can move in to squeeze the image by maximum 120 pixels horizontally and 80 pixels vertically. Top Right Horz Adjust (C) / Top Right Vert Adjust (D): Top right corner can move in to squeeze the image by maximum 120 pixels horizontally and 80 pixels vertically. Bottom Left Horz Adjust (G) / Bottom Left Vert Adjust (H): Bottom left corner can move in to squeeze the image by maximum 120 pixels horizontally and 80 pixels vertically. Bottom Right Horz Adjust (F) / Bottom Right Vert Adjust (E): Bottom right corner can move in to squeeze the image by maximum 120 pixels horizontally and 80 pixels vertically.BCADPIP/PBP menu36 EnglishH GE FPIP-PBP PIP / PBP Enable Main Source Sub Source Layout Size SwapSelectEnterOffTop Left SmallExitUSING THE PROJECTORPIP / PBP EnableToggle between displaying two sources at once (Main and PIP/PBP images) or one source only. Off: Display image from the main source only. PBP: Display images from two sources by separating the screen into two parts. One source isdisplayed on the main screen and another source is displayed in an inset window. PIP: Display images from two sources by separating the screen into half. One source is displayed on theleft side of the screen and the other source on the right side of the screen. For layout, refer to page 38. Main SourceSelect an active input to be used as the main image. The available inputs include VGA, HDMI-1, HDMI-2, DVI, and HDBaseT. Sub SourceSelect an active input to be used as the sub image. The available inputs include VGA, HDMI-1, HDMI-2, DVI, and HDBaseT. LayoutSet the location of the PIP/PBP image on the screen. Refer to page 38. SizeSelect the PIP/PBP size to small, medium, or large. SwapChange the main image to PIP/PBP, and the PIP/PBP to main image. Note: Swapping is available only when PIP/PBP is enabled.PIP/PBP Matrix PIP/PBP compatibility table as described below:PIP/PBP Matrix VGA DVI-DHDMI-2 HDMI-1 HDBaseTVGA -- V V V VDVI-D V -- V -- --HDMI-2 V V -- V VHDMI-1 V -- V -- --HDBaseT V -- V -- --Note: 1. Flashing lines may occur if the bandwidth of both inputs are too high, please try to reduce the resolution.2. Frame tearing may occur due to a difference in frame rate between the Main and the Sub picture, please try to match the frame rate for each input.English 37USING THE PROJECTORLayout and Size A P indicates the primary source region (lighter color):PIP Layout PIP-Bottom RightSmallPPIP Size MediumPPPPIP-Bottom LeftPIP-Top Left PIP-Top RightPBP Layout PBP, Main LeftP PSmall ±PPPBP Size Medium±PBP, Main Right±±LargeP PP PLargeP P38 EnglishUSING THE PROJECTORSettings menuLanguage Menu LocationStandby Power Mode Test Pattern Direct Power On Hot-Key Settings Reset to Default ServiceSettingsEnglishCommunication Mode Checkerboard OffBlank ScreenSelectEnterExitLanguageSelect an available language for the on-screen display. The available options include English, Simplified Chinese, French, German, Italian, Japanese, Korean, Russian, Spanish, Portuguese, Indonesian, and Dutch.LanguageMenu Location Set up the on-screen display menu location. The available options include Left Top, Right Top, Center, Left Bottom, and Right Bottom.Menu LocationStandby Power Mode Set the standby power mode setting. 0.5W mode: The projector is in standby mode when connected to AC power. (<0.5W). Communication mode: The projector can be controlled via the LAN terminal during power standby.English 39USING THE PROJECTORTest PatternChoose the required internal test pattern to display. The available options include None, Grid, White, Black, Checkerboard, and Color Bars.Direct Power OnAutomatically turn the projector on when electrical power is connected. The available options inlcude On and Off.Hot-Key SettingsAssign a different function to the hot key on the IR remote keypad by highlighting the function in the list and pressing Enter. Choose a function that does not already have a dedicated button, and assign the hot key to that function, allowing you to quickly and easily use the chosen function. The available options include Blank Screen, Aspect Ratio, Freeze Screen, and Projector Info.Reset to DefaultRestore all settings to their default value. It does not reset network but it resets RS232.Light source menuLight Source Mode Constant PowerLight Source InfoLight Source Constant PowerSelectEnterExitLight Source Mode Set the light source mode. The available options include Constant Power, Constant Intensity, ECO 1, and ECO 2. Constant Power Set the value of the laser diode power. Light Source Info Display the total hours of the projector, the total hours of the laser diode that have been used and information on light sensor calibration.40 EnglishUSING THE PROJECTOROptions menuBackground Color Auto Shutdown Sleep Timer Lens Function High Altitude PINRemote Settings Show message LED settings InformationOptions LogoOff OffSelectEnterExitBackground Color Use this feature to display a Logo, Blue, Black, or White screen when no signal is available. Auto Shutdown Automatically turn the projector off after no signals are detected for a preset number of minutes. If an active signal is received before the projector powers down, the image is displayed. Sleep Timer Allow the projector to automatically power off after it has been on for a specified amount of time.English 41USING THE PROJECTORLens Function Adjust the lens parameters. Focus: Adjust the focus point of the image. Zoom: Adjust the zoom of the image in or out. Lens Shift: Shift the lens up and down, or left and right. Lens Memory: Save the current lens position after doing lens shift. Apply lens position to the chosen set of lens memory. The lens memory can save up to five locations. Lock Lens Motors: Select this function to prevent all lens motors from moving. It will disable the Zoom, Focus, Horizontal, and Vertical Position settings, effectively locking out any changes and overriding all other lens features. This is particularly useful to prevent accidental lens position changes in multi-projector installations. Lens Calibration: Calibrate to move the lens back to center.Lens FunctionFocusZoomLens ShiftLens LockOnLens CalibrationSelectEnterExitHigh AltitudeEnable or disable high altitude mode. PINOn: Enable high altitude mode for altitudes 2000m. The fan operates at high speed to ensure sufficient air flow for high altitudes.Off: Disable high altitude mode. For altitudes below 2000m.Protects your projector with a PIN code. Once enabled, you must enter the PIN code before you can project an image. PIN Protect: Set to On to enable the function. Change PIN: Set a new PIN code.PINPIN protectOffChange PINSelectEnterExitRemote Settings Turn on or off remote settings, such as Top, Front, HDBaseT, and Projector Address. Show Message Hide or display projector settings. LED Settings Control the keypad LED and status LED. Information Display the projector settings. (Read-only).42 EnglishUSING THE PROJECTOR3D menu3D3D Invert3D Format [emailprotected] 3D Sync Out Frame Delay L/R Reference DLP Link3D Auto OffTo Emitter1ST Frame OffSelectEnterExit3D Enable 3D content detection. 3D Invert Invert the 3D sync signal when using a single projector. 3D Format Set the 3D format. Supports mandatory 3D formats and frame sequential [emailprotected] The available options include Frame Packing, Side-by-Side (Half), Top and Bottom, and Frame Sequential. [emailprotected] Set the 3D resolution [emailprotected] sequency. The available options include 96Hz and 144Hz. 3D Sync Out Transmit a 3D sync signal by the 3D sync output corrector to the emitter or to the next projector for 3D blending purposes. Frame Delay Correct asynchronous displaying of images under 3D blending. L/R Reference Source of the left or right reference. 1ST Frame: This is used for single 3D projector. DLP LinkField GPIO: Select Field GPIO to make the first 3D output signal the same for multiprojectors application.Select to use optimized settings for DLP 3D Glasses.English 43USING THE PROJECTORCommunications menuCommunicationsLANNetworkSerial Port Baud RateSerial Port EchoOnSerial Port PathSelectEnterExitLAN Determine the communication settings. DHCP: Turn the DHCP on or off. IP Address: Assign the network IP address. Subnet Mask: Assign the network subnet mask. Default Gateway: Assign the network default gateway. MAC Address: Display the network MAC address value. Apply: Apply the LAN configuration when the setting is changed or added. Network Determine the network settings. Projector Name: Display the projector name. Show Network Messages: Turn network messages on or off. Restart Network...: Restart the network. Network Factory Reset...: Performs factory reset on the network settings. The Projector Name, IPAddress (LAN), Start IP and End IP, and SNMP settings can be reset.Serial Port Baud Rate Select the serial port and baud rate. The available options include 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, and 115200. Serial Port Echo Control whether the serial port echoes characters. Serial Port Path Sets the serial port path to RS232 or HDBaseT.44 EnglishUSING THE PROJECTORHow to use web browser to control your projector 1. Turn "On" the DHCP option on projector to allow a DHCP server to automatically assign an IP address. 2. Open the web browser in your PC and type in the projector's IP address ("SETUP: Communications > LAN > IP Address").Note: The steps in this section is based on Windows 7 operating system. Making a direct connection from your computer to the projector* (For Windows 7 or higher)1. Turn "Off" the DHCP option on the projector. 2. Configure the IP address, Subnet Mask, and Gateway on projector. Refer to page 44. 3. Open Network and Sharing Center page on your PC, and assign the identical network parameters toyour PC as set on projector. Click "OK" to save the parameters. Note: The last group (ex: 100) of the IP address should be different from the projector. Make sure thenetwork parameters (i.e. other groups of the IP address and the Subnet mask) are similar to those shown in the OSD menu.4. Open the web browser on your computer and type the projector IP address into the URL field, then press "Enter".English 45USING THE PROJECTORSetup network control settings menuLAN_RJ45 function For simplicity and ease of operation, the projector provides diverse networking and remote management features. The LAN / RJ45 function of the projector through a network, such as remotely manage: Power On / Off, Brightness and Contrast settings. Also you can view the projector status information, such as: Video- Source, etc.Projector(Ethernet)Wired LAN terminal functionalities This projector can be controlled by using a PC (laptop) or other external device via RJ-45 connector and compatible ith Crestron / Extron / AMX (Device Discovery) / PJLink. Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. Extron is a registered trademark of Extron Electronics, Inc. of the United States. AMX is a registered trademark of AMX LLC of the United States. PJLink applied for trademark and logo registration in Japan, the United States of America, and othercountries by JBMIA. The projector is supported by the specified commands of the Crestron Electronics controller and related software,for example RoomView®.http://www.crestron.com/ This projector is compliant to support Extron device(s) for reference.http://www.extron.com/ This projector is supported by AMX (Device Discovery).http://www.amx.com/ This projector supports all commands of PJLink Class1 (Version 1.00).http://pjlink.jbmia.or.jp/english/ For more detailed information about the various types of external devices which can be connected to the LAN / RJ45 port and remote control the projector, as well as the supported commands for these external devices, please contact the Support-Service directly.46 EnglishUSING THE PROJECTORLAN RJ45 (For Windows XP) 1. Connect an RJ45 cable to RJ-45 connector on the projector and the PC (laptop).2. On the PC (Laptop), select Start > Control Panel > Network Connections.3. Right-click on the Local Area Connection, and select Property. 4. In the Properties window, select the General tab, and select Internet Protocol (TCP / IP).English 47USING THE PROJECTOR5. Click "Properties".6. Type in the IP address and Subnet mask, then press "OK".7. Press the "Menu" button on the projector. 8. Select Communications > LAN. 9. Enter the following connection parameters:± DHCP: Off ± IP Address: 10.10.10.10 ± Subnet Mask: 255.255.255.0 ± Default Gateway: 0.0.0.0 10. Press "Enter" to confirm settings. 11. Open a web browser, for example Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher installed. 12. In the Address bar, input the projector's IP address: 10.10.10.10.13. Press "Enter".48 EnglishUSING THE PROJECTORThe projector is setup for remote management. The LAN / RJ45 function displays as follows:Main pageNetwork Setting pageConfigurations pageInformation pageEnglish 49USING THE PROJECTORRS232 by Telnet Function There is alternative RS232 command control way, in projector so called "RS232 by TELNET" for LAN / RJ45 interface. Quick Start-Guide for "RS232 by Telnet" Check and get the IP address on OSD of the projector. Make sure that the PC / laptop can access the web-page of the projector. Make sure that "Windows Firewall" setting is set disabled in case of "TELNET" function filtering out byPC / laptop.1. Select Start > All Programs.> Accessories > Command Prompt.2. Input the command format as follows: ± telnet ttt.xxx.yyy.zzz 3023 ("Enter" key pressed) ± (ttt.xxx.yyy.zzz: IP-Address of the projector)3. If Telnet-Connection ready, and user can have RS232 command input, then "Enter" key pressed, the RS232 command will be workable.Specification for "RS232 by TELNET": 1. Telnet: TCP. 2. Telnet port: 3023 (for more detail, kindly please get contact with the service agent or team). 3. Telnet utility: Windows "TELNET.exe" (console mode). 4. Disconnection for RS232-by-Telnet control normally: Close 5. Windows Telnet utility directly after TELNET connection ready. ± Limitation 1 for Telnet-Control: there is less than 50 bytes for successive network payload for Telnet-Control application. ± Limitation 2 for Telnet-Control: there is less than 26 bytes for one complete RS232 command for Telnet-Control. ± Limitation 3 for Telnet-Control: Minimum delay for next RS232 command must be more than 200 (ms).50 EnglishADDITIONAL INFORMATIONCompatible resolutionsTiming Table Signal TypePCResolution640x350 640x400 640x480 640x480 640x480 640x480 640x480 720x400 720x400 768x480 768x480 768x480 800x600 800x600 800x600 800x600 800x600 800x600 800x600 848x480 848x480 848x480 848x480 960x600 960x600 960x600 960x600 1024x768 1024x768 1024x768 1024x768 1064x600 1064x600 1064x600 1064x600 1152x720 1152x720 1152x720 1152x720 1152x864 1152x864 1152x864 1152x864 1224x768 1224x768Frame rate (Hz)85 85 59 60 72 75 85 60 85 60 75 85 50 56 60 72 75 85 120 50 60 75 85 50 60 75 85 60 75 85 120 50 60 75 85 50 60 75 85 60 70 75 85 50 60VGAV V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V VHDMI-1/ HDMI-2V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V V VDVIHDBaseTVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVEnglish 51ADDITIONAL INFORMATIONSignal Type PCResolution1224x768 1280x720 1280x720 1280x720 1280x720 1280x720 1280x768 1280x768 1280x768 1280x800 1280x800 1280x800 1280x800 1280x960 1280x960 1280x960 1280x960 1280x1024 1280x1024 1280x1024 1280x1024 1356x960 1356x960 1356x960 1356x960 1360x768 1360x768 1360x768 1360x768 1366x768 1400x900 1400x1050 1400x1050 1400x1050 1440x900 1440x900 1600x900 1600x1200 1600x1200 1680x1050 1680x1050 1680x1050 1704x960 1704x960 1704x960 1704x960 1728x1080 1728x1080Frame rate (Hz) 85 50 60 75 85 120 60 75 85 50 60 75 85 50 60 75 85 50 60 75 85 50 60 75 85 50 60 75 85 60 60 50 60 75 60 75 60 50 60 50 60 75 50 60 75 85 50 6052 EnglishVGAV V V V V V V V V V V V V V V V V V V V V -- -- -- -- V V V V V V V V V V V V V V V V V V V V V V VHDMI-1/ HDMI-2V V V V V V V V V V V V V V V V V V V V V -- -- -- -- V V V V VV V V V V V V V V V -- V V -- -- V VDVIHDBaseTVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV--V--V--V--VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVV----VVVV--------VVVVADDITIONAL INFORMATIONSignal Type PCSDTV EDTVHDTVMandatory 3D Framesequential 3DResolution1864x1050 1864x1050 1864x1050 1920X1080 1920X1080 1920X1200RB 1920X1200RB 2128x1200480i 576i 480p 576p 1080i 1080i 1080i 720p 720p 720p 1080s 1080s 1080p 1080p 1080p 1080p 1080p 1080p 1080p 1080p Frame Packing 1080p Frame Packing 720p Frame Packing 720p Side by Side 1080i Side by Side 1080i Top and Bottom 720p Top and Bottom 720p Top and Bottom 1080p 1024x768 1280x720Frame rate (Hz) 50 60 75 50 60 60 50 60 60 50 60 50 25 29 30 50 59 60 23 24 23 24 25 29 30 50 59 602450605060506024120 120Note: "RB" means "reduced blanking".VGAV V V V V V V V V V V V V V V V V V -- -- V V V V V V V V------------------ VHDMI-1/ HDMI-2V V -- V V V V -- V -- V V V V V V V V -- -- V V V V V V V VVVVVVVVVV VDVIHDBaseTVVVV----VVVVVVVV----VV----VVVVVVVVVVVVVVVVV--V--VVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVVEnglish 53ADDITIONAL INFORMATIONEDID TableEstablished Timing: 720x400 @ 88 Hz 640x480 @ 60 Hz 640x480 @ 67 Hz 640x480 @ 72 Hz 640x480 @ 75 Hz 800x600 @ 56 Hz 800x600 @ 60 Hz 800x600 @ 72 Hz 800x600 @ 75 Hz 832x624 @ 75 Hz 1024x768 @ 60 Hz 1024x768 @ 70 Hz 1024x768 @ 75 Hz 1280x1024 @ 75 Hz 1152x870 @ 75 HzEstablished Timing: 720x400 @ 70 Hz 720x400 @ 88 Hz 640x480 @ 60 Hz 640x480 @ 67 Hz 640x480 @ 72 Hz 640x480 @ 75 Hz 800x600 @ 56 Hz 800x600 @ 60 Hz 800x600 @ 72 Hz 800x600 @ 75 Hz 832x624 @ 75 Hz 1024x768 @ 60 Hz 1024x768 @ 70 Hz 1024x768 @ 75 Hz 1280x1024 @ 75 Hz 1152x870 @ 75 HzWUXGA / VGA Standard Timing: 1440x900 @ 75 Hz 1280x800 @ 75 Hz 1280x1024 @ 60 Hz 1360x765 @ 60 Hz 1440x900 @ 60 Hz 1400x1050 @ 60 Hz 1600x1200 @ 60 Hz 1680x1050 @ 60 HzWUXGA / DVI-D Standard Timing: 1024x768 @ 120 Hz 1280x800 @ 75 Hz 1280x1024 @ 60 Hz 1360x765 @ 60 Hz1400x1050 @ 60 Hz 1600x1200 @ 60 Hz 1680x1050 @ 60 HzDetail Timing: 1366x768 @ 60 Hz 1920x540 @ 60 Hz 1920x540 @ 50 Hz 720x480 @ 60 Hz 1360x768 @ 60 HzDetail Timing: 1360x768 @ 60 Hz 1366x768 @ 60 Hz 1920x540 @ 60 Hz 720x480 @ 60 Hz54 EnglishADDITIONAL INFORMATIONEstablished Timing: 720x400 @ 70 Hz 720x400 @ 88 Hz 640x480 @ 60 Hz 640x480 @ 67 Hz 640x480 @ 72 Hz 640x480 @ 75 Hz 800x600 @ 56 Hz 800x600 @ 60 Hz 800x600 @ 72 Hz 800x600 @ 75 Hz 832x624 @ 75 Hz 1024x768 @ 60 Hz 1024x768 @ 70 Hz 1024x768 @ 75 Hz 1280x1024 @ 75 Hz 1152x870 @ 75 HzWUXGA / HDMI & HDBaseT Standard Timing:1024x768 @ 120 Hz 1280x800 @ 75 Hz 1280x1024 @ 60 Hz 1280x720 @ 120 Hz1400x1050 @ 60 Hz 1600x1200 @ 60 Hz 1680x1050 @ 60 HzDetail Timing: 720x576 @ 50 Hz 1280x720 @ 60 Hz 1920x540 @ 60 Hz 720x480 @ 60 HzEnglish 55ADDITIONAL INFORMATIONImage size and projection distancePlatform DMD Projection LensThrow RatioZoom Ratio Throw DistanceProjection screen size Throw RatioDiagonal (inch)50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 250 300 350Height (m)0.67 0.81 0.94 1.08 1.21 1.35 1.48 1.62 1.75 1.88 2.02 2.15 2.29 2.42 2.56 2.69 3.37 4.04 4.71Width (m)1.08 1.29 1.51 1.72 1.94 2.15 2.37 2.58 2.80 3.02 3.23 3.45 3.66 3.88 4.09 4.31 5.38 6.46 7.54A160.361 (120")N/A0.93~ 2.65mA01 0.95-1.221.28X 1.02~7.88m0.361 (120")0.951.22Min (m)Max (m)NA1.02 1.31NA1.23 1.58NA1.43 1.84NA1.64 2.10NA1.84 2.36NA2.05 2.63NA2.25 2.890.962.463.151.042.663.421.112.863.681.183.073.941.263.274.201.333.484.471.403.684.731.483.894.991.554.095.261.915.126.572.286.147.882.65WUXGA (16:10)0.67"A02A031.22-1.531.52-2.92A13 2.90-5.50A15 0.75-0.951.25X 1.31~9.89m1.9X 1.64~18.87m1.9X 3.12~35.54m1.26X 0.81-6.14mProjection distance (m)1.221.531.522.922.95.50.750.95Min (m)Max (m)Min (m)Max (m)Min (m)Max (m)Min (m)Max (m)1.311.651.643.143.125.920.811.021.581.981.963.773.757.110.971.231.842.312.294.404.378.291.131.432.102.642.625.035.009.481.291.642.362.972.955.665.62 10.66 1.451.842.633.303.276.296.25 11.85 1.622.052.893.633.606.926.87 13.03 1.782.253.153.953.937.557.50 14.22 1.942.463.424.284.268.188.12 15.40 2.102.663.684.614.588.818.74 16.59 2.262.863.944.944.919.439.37 17.77 2.423.074.205.275.24 10.06 9.99 18.95 2.583.274.475.605.57 10.69 10.62 20.14 2.753.484.735.935.89 11.32 11.24 21.32 2.913.684.996.266.22 11.95 11.87 22.51 3.073.895.266.596.55 12.58 12.49 23.69 3.234.096.578.248.18 15.72 15.62 29.62 4.045.127.889.899.82 18.87 18.74 35.54 4.856.14N/Aprojected imageV projected image heightH projected image widthA02/A15projected imageV projected image heightH projected image widthA01/A03/A1356 EnglishADDITIONAL INFORMATIONProjector dimensions and ceiling mount installation1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount tothe projector meet the following specifications: Screw type: M6 x 4 Minimum screw length: 20mm206.3Lens195.0484.0140.0140.0310.0509.0529.0Unit: mm Note: Please note that damage resulting from incorrect installation will void the warranty.Warning: If you buy a ceiling mount from another company, please be sure to use the correct screw size.Screw size will vary depending on the thickness of the mounting plate. Be sure to keep at least 30mm (3cm) gap between the ceiling and the bottom of the projector. Avoid installing the projector near a heat source.English 57ADDITIONAL INFORMATIONIR remote codesONOFF123456789Info 0 ModeAutoInputEnterMenuExitGamma Bright Cont. PIPLens HFocusLens VKeystone HZoomKeystone VShutter (AV Mute)Hot KeyPatternKey RepeatAddressDataKey LegendPosition Format Byte 1 Byte 2 Byte 3 Byte 4DescriptionON ( )1F132CD02FD Press to turn on the projector.OFF ( )21324F132CD2ED1 Press to turn off the projector.F132CD728D Use as numeric keypad number "1".F132CD738C Use as numeric keypad number "2".35F132CD748B Use as numeric keypad number "3".46F132CD758A Use as numeric keypad number "4".57F132CD7788 Use as numeric keypad number "5".58 EnglishADDITIONAL INFORMATIONKey Repeat Key LegendPosition Format68F179F1810F1911F1Info12F10 Mode13F114F1Auto15F1Input16F1UP ()17F1LEFT ()18F1Enter19F1RIGHT ()20F1DOWN ()21F1Menu22F1Exit23F1Gamma24F1Bright25F1Cont.26F1PIP27F1Lens H28F1Lens H 29F1Focus 30F1Lens V 31F1Lens V 32F1Focus 33F1Keystone Keystone34F135F1Zoom 36F1Keystone Keystone37F138F1Zoom 39F1Shutter (AV Mute)40F1Hot Key41F1Pattern42F1AddressDataByte 1 Byte 2 Byte 3 Byte 4Description32CD7887 Use as numeric keypad number "6".32CD7986 Use as numeric keypad number "7".32CD807F Use as numeric keypad number "8".32CD817E Use as numeric keypad number "9".32CD827D Press to display source image information.32CD25DA Use as numeric keypad number "0".32CD05FA Press to select the preset display mode.32CD04FBPress to automatically synchronize the projector to the input source.32CD18E7 Press to select an input signal.32CD0FF0Press to select items or make adjustments to our selection.32CD11EEPress to select items or make adjustments to our selection.32CD14EB Press to confirm your item selection.32CD10EFPress to select items or make adjustments to our selection.32CD12EDPress to select items or make adjustments to our selection.32CD0EF1Press to display the on-screen display menus for projector.32CD2AD5Press to return to previous level or exit menus if at top level.32CD2BD4 Press to adjust mid-range levels..32CD28D7 Press to adjust amount of light in the image.32CD29D6 Press to adjust difference between dark and light.32CD43BC Press to turn on/off the PIP/PBP function.32CD41BE Press to adjust the position of the image horizontally.32CD42BD32CD8679Press to adjust focus to improve image clarity as desired.32CD34CB Press to adjust the position of the image vertically.32CD32CD Press to adjust the position of the image vertically.32CD26D9Press to adjust focus to improve image clarity as desired.32CD8778 Press to adjust the vertical keystone.32CD51AE Press to adjust the vertical keystone.32CD52ADPress to adjust zoom to achieve a desired image size.32CD53AC Press to adjust the horizontal keystone.32CD54AB Press to adjust the horizontal keystone.32CD55AAPress to adjust zoom to achieve a desired image size.32CD56A9 Press to hide/unhide the screen picture.32CD57A8 Press to select your preset keys quickly.32CD58A7 Press to display a test pattern.English 59ADDITIONAL INFORMATIONTroubleshootingIf you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center.Image problemsNo image appears on-screen Ensure all the cables and power connections are correctly and securely connected as described in the "Installation" section. Ensure the pins of connectors are not crooked or broken. Ensure that the "Shutter (AV Mute)" feature is not turned on.Image is out of focus Press the Focus or Focus button on the remote control to adjust the focus until the image is sharp and legible. Make sure the projection screen is between the required distance from the projector. (Please refer to page 56).The image is stretched when displaying 16:10 DVD title When you play anamorphic DVD or 16:10 DVD, the projector will show the best image in 16:10 format on projector side. If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD. Please setup the display format as 16:10 (wide) aspect ratio type on your DVD player.Image is too small or too large Press the Zoom or Zoom button on the remote control to increase or decrease the projected image size. Move the projector closer to or further from the screen. Press "Menu" on the projector panel, go to "Screen > Aspect Ratio". Try the different settings.Image has slanted sides: If possible, reposition the projector so that it is centered on the screen and below the bottom of the screen. Use "Screen > Geomteric Correction > V. Keystone or H. Keystone" from the OSD to make an adjustment.Image is reversed Select "Screen > Rear Projection > On" from the OSD to reverse the image so you can project from behind a translucent screen.Other problemsThe projector stops responding to all controls60 EnglishIf possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power.ADDITIONAL INFORMATIONRemote control problemsIf the remote control does not work Check the operating angle of the remote control is pointed within ±30° (horizontally or vertically) to the IR receivers on the projector. Make sure there are not any obstructions between the remote control and the projector. Move to within 10 m (32.8 ft) of the projector. Make sure batteries are inserted correctly. Replace batteries if they are exhausted.Warning indicatorsLED status indicators The LED status indicators are located on the rear of the projector. Each LED is defined below.MessageStandby StatePower on (Warm up)Power on &Laser diode onPower off (Cooling down)AV mute is off (Image is displayed)AV mute is on (Image is black)Projector communicationFirmware upgradeLaser diode time has expiredUnit loses over 60% initial luminanceError (Over temperature)Error (Fan failure)GreenSteadySteady Steady SteadyLightStatusOrangeRedGreen OrangeRedFlashingFlashingSteadyFlashingSteadySteadySteady Flashing Flashing FlashingFlashingSteady FlashingAV Mute Green OrangeSteadySteady SteadySteadyEnglish 61ADDITIONAL INFORMATION Power off:Power Off? Press power key again.LAN Control Setting:LAN Control AMX Crestron PJ-Link Telnet HttpPort 9131 41794 4352 3023 8062 EnglishADDITIONAL INFORMATIONSpecificationsOpticalResolutionLens Laser Diode Image size (diagonal) Projection distanceDescription Native Resolution: WUXGA (1920x1200) Supported Resolution: Up to [emailprotected] (Reduced Blanking) Power Zoom/Focus and full lens shift [emailprotected] / Tc 60° 50~350" Please refer to "Image size and projection distance" table on page 56.Electrical Inputs OutputsControl port Power requirement Input currentDescription 1 x HDMI (version1.4) (with locking screw) 1 x DVI-D (only support digital signal) 1 x VGA IN (D-Sub 15pin) (Computer In or Component) 1 x HDBaseT 1 x 3D SYNC IN 1 x VGA Out (Support VGA loops through to monitor) (Monitor Out) 1 x 3D SYNC Out 1 x RS232 (D-sub 9 pin) (PC Control) 1 x Wired In (3.5mm phone jack) (Remote In) 1 x USB type A (for WiFi dongle purpose) 1 x Mini USB (for LAN FW upgrade only) (Service) 1 x RJ45 (LAN) 2 x IR Receiver (On the Front side and Top side) AC 100V - 240V, 50/60Hz 7.0AMechanical Installation orientation Dimensions Weight Environmental conditionsDescription Table Top, Ceiling Mount, Portrait 484 (W) x 509 (D) x 185 (H) mm (without lens, w/o elevators) 17 kg (without lens) Operating: 5~40°C, 10~85%RH, non-condensingNote: All specifications are subject to change without notice.English 63Optoma global officesFor service or support, please contact your local office.USA3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.com888-289-6786 510-897-8601 [emailprotected]Japan3-25-18 :0120-380-495[emailprotected] www.os-worldwide.comCanada3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.comLatin America3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.comEuropeUnit 1, Network 41, Bourne End Mills Hemel Hempstead, Herts, HP1 2UJ, United Kingdom www.optoma.eu Service Tel : +44 (0)1923 691865Benelux BVRandstad 22-123 1316 BW Almere The Netherlands www.optoma.nl888-289-6786Taiwan510-897-860112F., No.213, Sec. 3, Beixin Rd.,[emailprotected] Xindian Dist., New Taipei City 231,Taiwan, R.O.C.+886-2-8911-8600 +886-2-8911-6550 [emailprotected]www.optoma.com.twasia.optoma.com888-289-6786 510-897-8601Hong Kong[emailprotected] Unit A, 27/F Dragon Centre,79 Wing Hong Street,Cheung Sha Wan,Kowloon, Hong Kong+852-2396-8968 +852-2370-1222 www.optoma.com.hk+44 (0) 1923 691 800 +44 (0) 1923 691 888 [emailprotected]China5F, No. 1205, Kaixuan Rd., Changning District Shanghai, 200052, China+31 (0) 36 820 0252 +31 (0) 36 548 9052+86-21-62947376 +86-21-62947375 www.optoma.com.cnFranceBâtiment E 81-83 avenue Edouard Vaillant 92100 Boulogne Billancourt, France+33 1 41 46 12 20 +33 1 41 46 94 35 [emailprotected]SpainC/ José Hierro,36 Of. 1C 28522 Rivas VaciaMadrid, Spain+34 91 499 06 06 +34 91 670 08 32DeutschlandWiesenstrasse 21 W D40549 Düsseldorf, Germany+49 (0) 211 506 6670 +49 (0) 211 506 66799 [emailprotected]ScandinaviaLerpeveien 25 3040 Drammen NorwayPO.BOX 9515 3038 Drammen Norway+47 32 98 89 90 +47 32 98 89 99 [emailprotected]KoreaWOOMI TECH.CO.,LTD. 4F, Minu Bldg.33-14, Kangnam-Ku, Seoul,135-815, KOREA korea.optoma.com+82+2+34430004 +82+2+34430005www.optoma.com

References

Adobe InDesign CS5 (7.0.4) Adobe PDF Library 9.9
Top Articles
Latest Posts
Article information

Author: Frankie Dare

Last Updated: 12/07/2022

Views: 6497

Rating: 4.2 / 5 (73 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Frankie Dare

Birthday: 2000-01-27

Address: Suite 313 45115 Caridad Freeway, Port Barabaraville, MS 66713

Phone: +3769542039359

Job: Sales Manager

Hobby: Baton twirling, Stand-up comedy, Leather crafting, Rugby, tabletop games, Jigsaw puzzles, Air sports

Introduction: My name is Frankie Dare, I am a funny, beautiful, proud, fair, pleasant, cheerful, enthusiastic person who loves writing and wants to share my knowledge and understanding with you.